miter line in engineering drawing

jerroldhorita38674 April 26, 2022 drawing , engineering , in , line Comment

J type Chain THICK. They are lines with pointed edges at one or both ends.

Over Engineered Miter Saw Station Plans Etsy In 2022 Mitre Saw Station Miter Saw Engineering Design Process

B type Continuous THIN.

. K type Chain THIN Double Dash. Section lines are drawn as thin 35 mm black lines using an H or 2H pencil. - When a thick line ends at right angles to a thin line I want it to Butt to the thin line.

G type Chain Thin. 15 Engineering Drawing MCQs and Answers Set-V. It is used for ghost outlines and bend.

Both receding axes are at 30 degrees to the horizontal. A fast and accurate method of constructing the side view once the top and front views are established is by using a. In an oblique drawing all of the following angles are commonly used for.

It is often the case that a two-view projection is all that is required. Engineering Drawing The primary unit of measurement for engineering drawings and design in the mechanical industries is the. Limitations of Miter Bend.

Engineering Drawing General Knowledge Objective Type Questions Answers for competitive exams. Drawing a plan I want to achieve the following results when plotting particularly with thick lines. Note carefully that the MITER LINE is drawn from where the lower TOP View line and left RIGHT View line intersect.

11 Engineering Drawing MCQs and Answers Set-I. Arrowhead Lines are used. The standard ISO 128 1982 states that the thickness of the thick or wide line should be chosen according to the size and type of the drawing from the following range.

C type Continuous THIN Freehand. 45 degree MITER LINE. Miter option on thick lines - Plotting.

However in a direct contradiction of this the standard ISO 128-24 1999 states that the thicknesses should be 025. The pointed edges are in the form of an arrow. The numbers of cut will be a maximum of 5.

Are given on the drawing Geometry - Geometric Tolerancing Allows for specification of tolerance for the geometry of a part separate from its size Questions Category. One and Two-View Drawings. Drawing Techniques The general purpose cast iron section line is drawn at a 45-degree angle and spaced 15 mm to 3 mm or more depending on the size of the drawing.

These short solved questions or quizzes are provided by Gkseries. A type Continuos Thick. Mechanical Engineering When the receding lines are true length and the projectors are at 45.

F type Dashes THIN. Another term for orthographic drawing or projection is. Following are the different types of lines used in engineering drawing.

At the end of dimensional lines. All faces are equally distorted. The PRECEDENCE OF LINES tells us that if a visible line and a hidden line coincide occupy the same position on the drawing we should.

Create what is call a MITER LINE this 45 line will be used to project hence Orthographic Projection lines from the TOP view to the RIGHT SIDE view or visa versa. 14 Engineering Drawing MCQs and Answers Set-IV. These short objective type questions with answers are very important for Board exams as well as competitive exams.

Miter bend can be fabricated with 2 3 4 5 miters. Computer Aided Manufacturing Width And Height Width And Depth Height And Width Orthographic Drawing. TERMS IN THIS SET 91 B.

As a general rule use 3mm spacing. H type Chain THIN and THICK. Draw only the visible line.

D type Continuous THIN Zig-Zag. The numbers of miters will be decided according to the pressure and temperature of the line. The section lines should be evenly spaced and of equal thickness and should be.

Poor strength because of the more number of joints. 12 Engineering Drawing MCQs and Answers Set-II. Application size range can vary from company to company.

Contents hide 1 What type of sketch uses a miter line. 13 Engineering Drawing MCQs and Answers Set-III. The frontal face appears in its true shape.

Drawing In an exploded assembly drawing it is customary for the drafter to use a _____ line to illustrate how parts fit together. The view at the top of figure 5-19 shows a single-view projection of an object. 5-19 Two View Projections.

The depth distances must be reduced. It is obvious that a top view of this object tells you everything you need to know except the. This line is similar to the Dash Thin Lines with Dots except that it has double dots within it.

A line parallel to a reference plane shows true length in that plane. Unfortunately using Butt Miter Butt seems to win the argument at joins and creates a staggered join. E type Dashes THICK.

Pin On Solidworks Sheet Metal

Over Engineered Miter Saw Station Plans Etsy Mitre Saw Station Miter Saw Engineering Design Process